深圳市九郡芯科电子科技有限公司

3590S技术参数

电气特性（Electrical Characteristics）    
    
标准阻值范围(Standard Resistance Range）..........................200 to 100K ohms    
阻值允许偏差(Resistance Tolerance）..........................................±5 %     
独立线性度(Independent Linearity)..........................................±0.25%    
有效旋转角度(Effective Electrical Angle)......................3600 ° +10 °, -0 °    
阻值(Absolute Minimum Resistance）......................1 ohm or 0.1 % maximum     
                                                            (whichever is greater)    
噪音(Noise)...................................................100 ohms ENR maximum    
耐电压(Dielectric Withstanding Voltage)(MIL-STD-202, Method 301)    
海平面（Sea Level）..............................................1,500 VAC minimum    
额定功率(Power Rating)(Voltage Limited By Power Dissipation or 450 VAC, Whichever is Less)    
  +40 °C..................................................................2 watts    
  +125 °C..................................................................0 watt    
绝缘电阻(Insulation Resistance)(500 VDC)....................1,000 megohms minimum    
分辨率(Resolution) ..................................See recommended part numbers    
    
环境特性(Environmental Characteristics)    
    
工作温度范围(Operating Temperature Range).......................+1 °C to +125 °C    
储存温度范围(Storage Temperature Range)........................-55 °C to +125 °C    
温度系数范围(Temperature Coefficient Over Storage Temperature Range2)    
.........................................................±50 ppm/°C maximum/unit    
震动(Vibration)...............................................................15 G    
电刷返回(Wiper Bounce).....................................0.1 millisecond maximum    
冲击(Shock)...................................................................50 G    
高温负荷寿命(Load Life).......................................1,000 hours, 2 watts    
总阻变化(Total Resistance Shift).....................................±2 % maximum    
旋转寿命(Rotational Life) (No Load)....................1,000,000 shaft revolutions    
总阻变化(Total Resistance Shift).....................................±5 % maximum    
防潮性(Moisture Resistance) (MIL-STD-202, Method 103, Condition B)    
总阻变化(Total Resistance Shift).....................................±2 % maximum    
防护等级(IP Rating)    
密封对象（Sealed Versions） (-3, -4, -7, and -8) ............................IP 65    
不密封对象(Unsealed Versions) (-1 -2, -5, and -6)............................IP 40    
    
机械特性(Mechanical Characteristics)    
    
终端止档强度 (Stop Strength)..........................45 N-cm (64 oz.-in.) minimum    
机械角度(Mechanical Angle)....................................3600 ° +10 °, -0 °    
扭矩(Torque) (Starting & Running).......0.35 N-cm (0.5 oz.-in.) maximum (unsealed)    
1.1 N-cm (1.5 oz.-in.) maximum (sealed)    
固定方式(Mounting)..............................55-80 N-cm (5-7 lb.-in.) (plastic)    
90-113 N-cm (8-10 in.-lb.) (metal)    
轴摆度(Shaft Runout).....................................0.13 mm (0.005 in.) T.I.R.    
横向摆动(Lateral Runout).................................0.20 mm (0.008 in.) T.I.R.    
轴端游隙(Shaft End Play).................................0.25 mm (0.010 in.) T.I.R.    
转轴径向跳动(Shaft Radial Play)..........................0.13 mm (0.005 in.) T.I.R.    
引导径向跳动(Pilot Diameter Runout)......................0.08 mm (0.003 in.) T.I.R.    
侧隙(Backlash)......................................................1.0 ° maximum    
重量(Weight)....................................................Approximately 19 G    
终端设备(Terminals).........................................Solder lugs or PC pins    
浸焊条件(Soldering Condition)    
手焊(Manual Soldering)...................96.5Sn/3.0Ag/0.5Cu solid wire or no-clean    
活性松香焊锡丝(rosin cored wire); 370 °C (700 °F) max. for 3 seconds    
波动焊接(Wave Soldering)...96.5Sn/3.0Ag/0.5Cu solder with no-clean flux; 260 °C (500 °F) max.    
for 5 seconds    
清洗过程(Wash processes)..........................................Not recommended    
标记(Marking)..........Manufacturer’s name and part number, resistance value and    
                    tolerance, linearity tolerance, wiring diagram, and date code.    
机械连接(Ganging )(Multiple Section Potentiometers).................1 cup maximum    
五金器具(Hardware).....One lockwasher and one mounting nut is shipped with each potentiometer.

我司郑重承诺所售产品均为原装！！！